Myenergi Zappi 3 22 kW - 3-Phase - 32A - type 2 - 6,5 meter - EV Charger - Pre-order
- The best wallbox to combine with pv-panels
- Built-in MID meter
- 3 year warranty
- Automatically switches between 1 and 3 phases
- Excellent service and complaint handling from Myenergi
Tethered Zappi 3: the Zappi EV Charger with MID meter and RFID
The myenergi tethered Zappi 3 is an EV Charger that charges your car with power from your own solar panels. Compared with the Zappi V2.1, it adds a built-in MID meter, an RFID reader and hardware for ISO 15118-20. Founded in Lincolnshire in 2016, British brand myenergi started with the Zappi and eddi and now also makes home batteries. You can control all these products in one app. This version has a permanently attached 6.5 m Type 2 charging cable, ready to plug in when you get home.
The Zappi 3 delivers up to 7.4 kW on a single-phase supply and up to 22 kW on a three-phase supply. If you upgrade your supply later, you can keep the same EV Charger. Browse our 22 kW EV Chargers to compare it with other brands.
- Automatic phase switching: charge from just 1.4 kW of surplus solar power, even on a three-phase supply.
- Two charging modes: in Smart mode, the Zappi 3 automatically uses surplus solar power, your charging schedules and your electricity tariff, including dynamic rates. In Fast mode, it starts charging immediately at full power.
- Lower charging costs with a dynamic tariff: the Zappi 3 uses your tariff to charge when electricity costs least.
- Boost Charge: hold the button for three seconds or tap Charge Now in the app to start a full charge immediately.
- Dynamic load balancing: the Zappi 3 uses only the power available after other appliances have been supplied. It comes with 3 CT clamps for wired measurement. A myenergi harvi can transmit the readings wirelessly.
- Built-in MID meter (Class B, 1%): records each kWh delivered so you can claim business charging expenses.
- RFID reader: one RFID tag is included. Register up to 127 tags per Zappi 3 to control who can charge.
- OCPP 1.6J (via the cloud) and a third-party API let you connect the Zappi 3 to a back office to view charging sessions, manage users and bill for the electricity supplied.
- Connectivity: Wi-Fi (2.4 GHz), Ethernet, 4G/LTE with your own nano-SIM and Bluetooth. Software updates are delivered automatically over the air.
- Free myenergi app: monitor and control your Zappi 3 remotely and see how much energy you generate, use and put into your car.
- V2G-ready: the hardware is designed for bidirectional charging under ISO 15118-20.
- Works with any inverter: the Zappi 3 measures surplus solar power itself, so you can use it across different systems.
- External control: a volt-free contact for a home energy management system (HEMS) or an inverter, for example.
- Built-in 6 mA DC residual current detection. An upstream residual current device is still required.
- LCD screen with multicolour status LED: see at a glance whether the Zappi 3 is charging, waiting for surplus solar power or following a schedule.
- IP65 and IK10: water- and impact-resistant, suitable for outdoor use and equipped with tamper detection.
- Supplied with a 6.5 m charging cable with a Type 2 plug.
- Three-year warranty, with an extension available.
Zappi 3 compared with Zappi V2.1
The table shows what has changed since the tethered Zappi V2.1.
| Feature | Zappi V2.1 22 kW with tethered cable | Zappi 3 with tethered cable |
|---|---|---|
| MID meter | No | Yes, MID Class B (1%) |
| ISO 15118-20 | No | Yes, hardware included |
| Access control | PIN code | RFID (13.56 MHz, Mifare) |
| Connectivity | Wi-Fi and Ethernet | Wi-Fi, Ethernet, 4G (LTE) and Bluetooth |
| Charging power | 22 kW (three-phase) | 7.4 kW single-phase or 22 kW three-phase |
| Weight | 7.2 kg | 6.6 kg |
| Enclosure | ABS | Polycarbonate (PC) |
Built-in MID meter for expense claims and Dutch ERE payments
A MID meter accurately measures how many kilowatt-hours go into your car. The Zappi 3 has a built-in meter certified to EN 50470, MID Class B. You can use its readings in two ways.
- In the Netherlands only, a registration service can register the kWh you charge at home for EREs (emission reduction units) on your behalf. The scheme also covers private individuals from 2026 and can provide a payment for eligible charging.
- If you drive for work, you can use the same meter readings to claim home charging costs from your employer.
For Dutch ERE payments, the MID meter must be built into the EV Charger itself. A separate meter in the distribution board does not qualify. This is why we recommend a built-in meter for most home charging setups. Browse our EV Chargers with a MID meter.
Charging with surplus solar power and dynamic tariffs
The Zappi 3 adjusts charging to your solar generation and electricity tariff. Automatic switching between one and three phases lets it start charging with just 1.4 kW of surplus solar power, even when your panels are generating relatively little. With a dynamic tariff, it charges during the cheapest hours.
Smart mode also follows your own charging schedules. Select Fast to charge immediately at full power. To override a schedule in Smart mode, hold the button on the EV Charger for three seconds or tap Charge Now in the app.
The Zappi 3 works with any brand or type of inverter, so you can keep your existing solar setup. Three wired CT clamps at the incoming supply measure your surplus solar power, one per phase. If the distribution board is a long way from the EV Charger, you can transmit the readings wirelessly with a myenergi Harvi. To see solar generation separately in the app, you will generally need three additional CT clamps.
The same readings enable dynamic load balancing. The EV Charger adjusts its current to the capacity available at your incoming supply, helping to protect the main fuse from overload. Compare the Zappi 3 with our other solar-compatible EV Chargers.
Hardware for bidirectional charging under ISO 15118-20
ISO 15118-20 is the communication standard between a vehicle and an EV Charger that enables features such as bidirectional charging. The Zappi 3 already has the necessary hardware. It cannot yet supply power back to your home or the grid. This requires software from myenergi and a compatible vehicle. A software release date has yet to be announced. If you want to export power from your car now, explore our bidirectional EV Chargers.
The same standard also enables Plug & Charge. A compatible vehicle is recognised automatically so you can start a session without a charging card or app. This feature is not active at delivery. Availability and timing depend on the software, your vehicle and your charging service.
From 1 January 2027, the EU’s AFIR regulation introduces new ISO 15118-20 requirements for charging points. Read what this means for charging at home in our article on ISO 15118-20 requirements for home EV Chargers.
RFID, 4G and the myenergi app
Use the built-in RFID reader to start a session with a tag or card and control who can charge on your driveway. One RFID tag is included, and you can register up to 127 tags on one EV Charger.
The Zappi 3 connects via Wi-Fi (2.4 GHz), Ethernet, Bluetooth or 4G. For 4G, you need your own nano-SIM with a data plan. No SIM card is supplied. Smart charging itself does not require a subscription.
For remote management, the Zappi 3 supports OCPP 1.6J, the open protocol between an EV Charger and its management system, and an API for third-party systems. Connect it to a back office to log sessions and bill for the electricity delivered. Myenergi sends software updates remotely over the internet.
What’s in the box?
- Myenergi Zappi 3 EV Charger (7.4 kW single-phase, 22 kW three-phase) with a 6.5 m tethered Type 2 charging cable (ZAPPI-4AP22T065B-T)
- 3 CT clamps for solar charging control and load balancing, one per phase
- 1 RFID tag
The three-year warranty can be extended to five years.
Installing the 22 kW Myenergi Zappi 3
Have the Zappi 3 installed by a qualified EV Charger installer. Myenergi specifies that only qualified electrical installers may fit the Zappi 3. Your installer commissions it via Bluetooth using the myenergi Installer Assistant app and can access technical support from the Netherlands. Here is what to take into account when planning the installation:
- The Zappi 3 has an adjustable current of up to 32 A. For the Dutch installation described here, the circuit is sized for 32 A per phase, with overcurrent protection of at least 40 A for single-phase or 40 A per phase for three-phase.
- Supply cable with a conductor cross-section of 4 to 10 mm².
- The Dutch installation described here uses an upstream 30 mA Type A residual current device in accordance with NEN 1010. For future V2G use, choose a device suitable for power flow in both directions.
- Surge protection is not built into the Zappi 3. The installer fits it in the distribution board where required.
- Choose your connection in advance: Wi-Fi is preferred (2.4 GHz only), with Ethernet (Cat5e, up to 100 m) or 4G/LTE with your own nano-SIM as alternatives.
- The CT clamps go on the incoming supply, one per phase. If the distribution board is some distance away, a myenergi harvi can transmit the readings wirelessly.
- Mount indoors or outdoors on a wall or a Zappi mounting post, preferably out of direct sunlight.
- Check the space available in your distribution board. An extension enclosure is often needed.
We recommend having your EV Charger installed by a qualified professional. Installation calls for specialist knowledge, and mistakes can have serious consequences. Qualified installers have completed relevant training, often including the manufacturer’s own course. To find out what it would cost to install your 22 kW Myenergi Zappi 3 EV Charger, contact us for a no-obligation quote.
If you are planning the installation at home, discuss the following points with your qualified installer. The cable designations and examples refer to the Dutch installation described here.
The example specifies an RCBO with a B-curve overcurrent characteristic with a current rating below the main supply protection rating. You also need the appropriate supply cable. The Dutch example for this 22 kW EV Charger uses 5 × 6 mm² YMVK cable indoors or in conduit, or 4 × 6 mm² YMVK-as underground cable outdoors. There are two ways to connect the meters for dynamic load balancing and solar monitoring. A Myenergi harvi can transmit readings to the Zappi by radio over a distance of up to 15 m, independently of Wi-Fi. For longer distances or where wireless transmission is unsuitable, use a data cable. To see solar generation separately in the myenergi app, you need three additional myenergi CT clamps. Connect them using a second harvi or an additional data cable to the distribution board. For distances over 15 m, this setup uses two data cables when both measurements are required.
Is there enough room in your distribution board? The RCBO used in this example takes up four modules, so an extension enclosure is often required.
For the installation instructions for this EV Charger, see the manuals below.
Installation costs for the Myenergi Zappi
Installation costs vary by site, particularly if a harvi or data cabling is needed. When we install a Zappi in the Netherlands, typical costs include the following (VAT included):
- Basic installation: €399
- Three-phase RCBO, including installation: €145.50
- YMVK-as 4 × 6 mm² cable per metre, installed: €10.95
- Cat 5 UTP cable per metre, including fitted connectors and installation: €5.11
- Configure load balancing via CT clamps or an external Modbus kWh meter: €199
Other common costs when installing a Myenergi Zappi include:
- Standard 110 × 220 extension enclosure, installed: €110.11
- Install a harvi for solar monitoring: €45.53
- Run an additional data/UTP cable: €55.00
- Additional Cat 5 UTP cable per metre, including fitted connectors and installation: €5.11
Other costs may apply depending on the site, for example if the EV Charger is installed on a mounting post. A mounting post often needs a concrete footing. You can find the full list of installation costs here on our website.
To book installation with us, add the basic installation to your basket. Any additional work and materials are billed at their actual cost.
Frequently asked questions about the tethered Zappi 3
Does the Zappi 3 have a MID meter?
Yes. The Zappi 3 has a built-in EN 50470 Class B MID meter. You can use its readings to claim home charging expenses. In the Netherlands only, the meter also meets the metering requirement for ERE payments through a registration service.
What is the difference between the Zappi V2.1 and the Zappi 3?
The Zappi 3 adds a built-in MID meter, RFID and hardware for ISO 15118-20. It also adds 4G and Bluetooth connectivity to the Wi-Fi and Ethernet options available on the V2.1.
Can the Zappi 3 supply power from my car to my home?
Not yet. The ISO 15118-20 hardware is built in, but supplying power back to your home requires software from myenergi and a compatible vehicle. A release date has yet to be announced.
Does the Zappi 3 support single-phase charging?
Yes. It charges at up to 7.4 kW on a single-phase supply or up to 22 kW on a three-phase supply, provided your car supports that AC charging power.
Do I need solar panels?
No. Without solar panels, the Zappi 3 charges from the grid and uses your electricity tariff to schedule charging. With panels, it can start charging from 1.4 kW of surplus solar power.
What colour is the Zappi 3?
The Zappi 3 is available in black only. The V2.1 was available in black or white.
Choose the tethered Zappi 3 EV Charger
Want to charge with your own solar power, use the built-in meter for Dutch ERE payments if you charge in the Netherlands, and have the hardware for bidirectional charging once the software is available? The tethered Zappi 3 EV Charger brings these features together in one wall-mounted unit. Prefer to choose your own cable length? Take a look at the Zappi 3 EV Charger with a socket.
Unsure which Zappi suits your car and home supply? Call Wallbox Discounter on +31 74 700 2114 or send a WhatsApp message to +31 6 34797985 for free advice. Explore the other models on our Zappi page.
Want to know more about the 22 kW Myenergi Zappi 3 EV Charger?
- Operation & Installation Manual
- Quick install guide
- vHub & WiFi set-up manual
- Brand: Myenergi
- Plug type: Type 2
- Number of Phases: 3 Phases
- Number of Amps per phase: 32A
- Maximum payload: 22 kW
- Charging cable length: 6,5 meter
- Display: Yes
- RFID Security: No, but it does have PIN protection
- Charging information: By display and app
- Controllable via app: Yes (myenergi App)
- Installation Instructions: Wall and post mounting possible
- Load Balancing: Dynamic
- Connectivity: WiFi & Ethernet
- Connection with solar panels: Yes
- Automatic 1-phase / 3-phase switching: Yes, in ECO+ mode starting at 1.4 kW of surplus power
- Suitable for charge cards: No
- Automatic settlement: Yes
- Communication protocol: OCCP 1.6J
- Subscription: No, no monthly costs
- Language manual: EN, NL, DE, IT, ES & FR
- Colour(s): Black or White
- Weight: 7.2 KG
- Sizes (excluding cables): 43,9 x 28,2 x 12,2 cm (h x w x d)
- Material: ABS 6 & 3 mm (UL 94)
- Protection degree: IP65 / IK10
- Impact resistance: IK10
- Operating temperature range: -25 °C to +40 °C
- Warranty period: 36 months
- MID Meter: No
- ISO 15118-20: No




















